Loading... Please wait...

Currency Displayed in

Currency Converter

Bump Steer Delete Tie Rod Kit (BSD)™ Can Am X3 64" and 72" Width Models **Discounted 10% (BLEMISHED)**

Hover over image to zoom

  • BSD Tie Rod kit (patent pending)
  • Image 2
  • Image 3
  • Stainless steel spacers and laser engraving
  • Custom machine work and high quality Teflon lined rod ends
  • Image 6
  • BSD Tie Rod kit installed
  • BSD Tie Rod kit installed (patent pending)

 Product Description

***These are BLEMISHED BSD tie rod kits for all width X3 models. There will be cosmetic defects in the anodizing and/or aluminum. The kits on this page are offered at 10% off of retail***


Can Am X3 RS Bump Steer Delete (BSD)™ Tie Rod Kit (Patented geometry location. Patent # 9,988,083 B1)


Our new BSD™ Tie rod kit is here and does wonders for your Can Am X3 RS. Through rigorous testing of our shop car, we found that the X3 RS had a lot of steering wheel feed back in the whoops especially if you run a larger tire and turning in the whoops. After cycling the front suspension we found over 4 inches of bump steer in the factory system. Bump steer is a change in toe setting (front of tires closer together than the rear of the tires) through the cycle of front suspension travel. The best set up is as close to zero toe change as possible. If your front tires change toe setting they are essentially doing the same thing as you turning the steering wheel slightly on every bump you hit.  Bump steer is one of the biggest contributors to steering wheel feedback, twitchy drive ability, excessive front end wear and worn out forearms from trying to keep the car straight. So in an effort to eliminate all of these things we developed our BSD™ (bump steer delete™) tie rod kit for the X3 RS. Our kit relocates the outer tie rod pivot point which changes the front end geometry and lowers the factory 4 inch bump steer measurement down to just 3/8 of an inch! With the bump steer removed the car is much easier to drive, steer and control. What used to be a two handed steering wheel grab to hold the car in whoops is now just a few fingers on one hand. Your front end parts will last longer. Your car will drive more predictably. Your forearms will have no arm pump. The whole driving experience will become easier. Don't wait, install our BSD™ Tie Rod Kit today


The factory car has ZERO adjust ability for alignment other than toe set. Caster and Camber can NOT be adjusted. Toe adjustment with our BSD kit will not affect any other aspect of the alignment since nothing else is adjustable. 





For all of you who may have already purchased a set of aftermarket tie rods for your X3 but want to fix your geometry with out buying the complete tie rod we have an answer for you. You can purchase our outer joint with the geometry fixing spacers and upgrade your aftermarket tie rods. You can buy these with the 5/8 Left Hand threaded rod ends or if you already have 5/8 rod ends in your tie rods you can just purchase the spacer kit.


(Patented geometry location. Patent # 9,988,083 B1)

Below is the complete joint kit $169.95 PN# 706-805-01.   We only sell this with the highest grade, Teflon lined, race style rod ends. They cost more but are necessary for steering components.

These are Left Hand threaded rod ends so make sure your tie rod kit uses Left Hand thread 




(Patented geometry location. Patent # 9,988,083 B1)

Below is just the BSD™ spacer upgrade kit $42.95 PN#707-805-01

If you have Assault Industries tie rods then all you need is this spacer kit below.


 Product Videos

How to Install: BSD Tie Rod Kit (Can Am Maverick X3 RS)
  • How to Install: BSD Tie Rod Kit (Can Am Maverick X3 RS)

 Other Details

Can Am:
17-19 X3 RS (72")
Can Am:
18-19 X3 RC (72")

 Find Similar Products by Category

Vendors Other Products

 Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

You Recently Viewed...

What's News


Follow us on

Copyright © 2020 Shock Therapy, LLC. All Rights Reserved.